Home > Packard Bell > Packard Bell Monitor Is Sick

Packard Bell Monitor Is Sick

Find out more about our cookie policy Gumtree Show more options Search Gumtree.com Messages Post an ad My Gumtree 1 Manage my Ads Messages Favourites My Alerts My Details Create Account Is there anything else. I have a newly released laptop with a messed up screen, and I can't find any websites selling the screen part # or model # at all. I also read somewhere that all manufacturers block screens that are not for their line of laptops through bios but i cannot confirm it. click site

It's possible that during the reassembly process you accidentally pulled the cable from the connector. I can see very dark icons. Is price important? It fits perfectly and all of the adapters match up (Inverter and Video Cable) When I turn on the screen it does not work it just displays lines everywhere. http://www.webdesignforums.net/forum/general-web-design-discussion/26676-my-sick-new-monitor-setup-woohoo.html

Subsequent tests confirmed his suspicion. If you get a display on the external screen im afraid it will likely require opening up the laptop and an engineer which usually (for good reason) is not cheap! forgot password? I took the screen off and reconnected the cables to make sure they were seated well.

Steve, you are a kid at heart aren't you?! I know the new screen is good. i wanted to replace it with a LTN150XG-01 matte screen but it doesnt work. Gary Gemmell July 3, 2010 | Could just be the laptop lid switch is jammed - check that first its always a first checkpoint before moving on.

Make sure the video cable is plugged correctly into the LCD screen. at the top of the screen where the ribbon hooks into the circuit board there is a large connector and a small connector. If the switch is not jammed closed then next suspect is the ccfl backlight - easily broken if you drop your laptop. http://www.checkpointdelta.net/showthread.php?3348-Battlefield-2-Trailer-SICK!/page2 Dan June 6, 2009 | Erich hochstuhl, I had a dc jack replaced on a laptop.

To check motherboard side of the cable I need to figure how to disassemble the thing, tried y’day without luck. when i push the on button the lights come on and then go off. cj2600 September 22, 2009 | cliff, I’ve checked and it’s the right screen etc and when I connected it to my monitor the lines are not there. I was able to use plyers and destroy the old screen (was already broke) to get the inverter bracket off that, then use a hammer to straighten it out.

Please try the following: Load the page again by clicking the Refresh button in your web browser. http://www.packardbell.com/pb/en/GB/content/productgroup/monitors Could that be the scenario of a broken motherboard? no name. Test your AC adapter with a voltmeter.

I messed with the connectors and when I unplug the cable and plug it in, it's very distorted. get redirected here I have the same thing with mine. Why a Xeon though? I have noticed that a pin from ribbon connector is not there so do you think that could be the issue?

In the future, he said, he expects the situation will be reversed and people will have more sensors than cars do. Still the only thing that comes on is the backlight. Click the like button below the post. navigate to this website No video on the screen.

I am not using the laptop hooked up to the desktop monitor…kinda defeating the purpose of a laptop! thanks cj2600 October 29, 2009 | James, When I look at the replacement it has no screw holes on the frame for the inverter or the piece on top (mounting bracket Automatic data analysis could spot patterns of outlier data points and flag the onset of ill health, providing an opportunity for intervention, prevention or cure.

everything works fine as swapped back the old one to post this.

It's hard to tell what is causing the problem. please reply as soon as possible. The LCD signal cable was attached with industrial strength tape on the old panel's connector. Yea but look at the experience you've gained.

Do you look for design, the latest technologies, or maximised connectivity? That was really interesting, and I thought it was great that the authors did that.” Topol noted that one of the biosensors used in the study doesn’t work very well and Thanks for quick response. http://nexwarecorp.com/packard-bell/packard-bell-pda.html Lets figure out step-by-step how to troubleshoot and  and fix the problem.

Now the laptop doesn't react to the power button at all. Matt November 2, 2010 | Hello, first of all thank you for making this website! Hey I just picked one of these together got it at the local wal-mart. Researcher Elizabeth Colbert, of the Veterans Affairs Palo Alto Health Care System, is also a co-author.

Make sure the adapter outputs correct voltage. Does your "bad laptop" turn on at all? Rob April 24, 2010 | I just replaced a crecked screen on my dell xps 1530 the back light comes on but nothing? Take a look inside the video connector on the motherboard/video card.

To find your way back, click here to go to our homepage. Maybe the button is dirty and got stuck inside the case. Are you getting same problem on the external video or not? Christian HC October 19, 2009 | Hi!